Marine Outfitters
VENOM = Clean Waterline !
While they last!
Save on Shipping
Currency: Canadian Pricing American Pricing


ARK Composites ARK 2:1 Slow Hardener

Usually Stocked Items normally ship immediately or in 1-2 business days. These items are returnable subject to our RETURN POLICY
Quick Access Items normally ship in 1-2 business days. Quick Access Items are returnable subject to our RETURN POLICY but with a restocking fee.
Special Order Items normally need a little extra time to be brought in from our suppliers � in some cases up to 7 business days. Special Orders are returnable subject to our RETURN POLICY but with a restocking fee.
Request Items may take a few days to obtain from our suppliers and pricing may need to be updated. Marine Outfitters will contact you to provide an approximate delivery date and confirmation of price. Request items cannot be returned!
 
Item / Price
Stock Type
Inventory On Hand 11/01 @ 04:06 PM
Product Code
Order Quantity
Gallon: 128 oz.
$231.99
Quick Access
ARK AHSG
Half Gallon: 64 oz.
$141.99
Quick Access
ARK AHS.5G
Quart: 32 oz.
$59.99
Quick Access
1
AHSQ
Pint: 16 oz.
$31.99
Quick Access
AHSP
8 oz.
$22.99
Quick Access
ARK AHS8
4oz.
$13.99
Quick Access
ARK AHS4


CUSTOM: ark-21-slow-hardener

ARK COMPOSITES EPOXY RESIN

2:1 RATIO CLEAR NO BLUSH LOW VISCOSITY SYSTEM

USED TO:

  • Coat and waterproof wood, metal, most porous surfaces.
  • Laminate with Fiberglass, Carbon, Kevlar
  • Glue, Fill, Fair with addition of fillers.

SURFACE PREP: Apply directly to clean dry wood.  For fibreglass or metal clean surface with Acetone or Lacquer thinner, sand with 220 grit or less, remove dust.  Do not use Varsol or petroleum based solvents.

MIXING: Mix 2 parts Ark Epoxy Resin with 1 part Ark Fast or Slow Hardener.  Use graduated containers or pumps to measure, don’t guess, too much or too little hardener will affect proper cure.  Mix thoroughly, scraping sides of the container, add fillers if desired, spread with solvent resistant Brush, Roller, or Squeegee. 

RECOATING: Recoat with ARK Epoxy resin as soon as the previous coat is tacky, 2 to 6 hours depending on hardener and temperature.  Sand with 80 grit after 6 hours or when the epoxy is hard enough to sand without clogging the paper.  Cleaning to remove blush is not necessary unless you are working in freezing rain. 

Recoat with Paint or Varnish after 7 day full cure.  Sand to 220 grit, remove dust with water and a clean cloth, allow to dry thoroughly for at least 1 hour before applying coating.  Two part Polyurethane coatings over Epoxy will last longer and be more scratch resistant than Enamel paints. 

POT LIFE and CURE TIMES:

Pot Life and sanding time will vary depending on temperature, mixed volume, time in the mixing container and laminate thickness.  Pot life and cure time will roughly double for a 8C drop in temperature, and ½ for an 8C rise.  

To extend working time pour the mixed epoxy into a paint tray or spread onto the work surface as soon as possible, a thin film will take longer to gel.  Volumes over 100 ml will get HOT if left in the mixing pot.

Fast and Slow hardeners are blendable to customise pot life and will cure as low as 5C.     

           

HARDENER

POT LIFE @ 22C/71F

WORKING

(GEL) TIME

SANDABLE

 

POT LIFE@

12C/54F

SANDABLE

FULL CURE

855 FAST

8 -10 MIN

15 -18 MIN

6 -8 HRS

18 – 20 MIN

12 – 14 HR

7 DAYS

856 SLOW

15-20 MIN

30 -35 MIN

10 – 12 HRS

35 – 40 MIN

20 – 24 HR

7 DAYS




Currency: Canadian Pricing American Pricing


ARK No Blush 2:1 Epoxy


ARK COMPOSITES EPOXY RESIN

2:1 RATIO CLEAR NO BLUSH LOW VISCOSITY SYSTEM

USED TO:

  • Coat and waterproof wood, metal, most porous surfaces.
  • Laminate with Fiberglass, Carbon, Kevlar
  • Glue, Fill, Fair with addition of fillers.

SURFACE PREP: Apply directly to clean dry wood.  For fibreglass or metal clean surface with Acetone or Lacquer thinner, sand with 220 grit or less, remove dust.  Do not use Varsol or petroleum based solvents.

MIXING: Mix 2 parts Ark Epoxy Resin with 1 part Ark Fast or Slow Hardener.  Use graduated containers or pumps to measure, don’t guess, too much or too little hardener will affect proper cure.  Mix thoroughly, scraping sides of the container, add fillers if desired, spread with solvent resistant Brush, Roller, or Squeegee. 

RECOATING: Recoat with ARK Epoxy resin as soon as the previous coat is tacky, 2 to 6 hours depending on hardener and temperature.  Sand with 80 grit after 6 hours or when the epoxy is hard enough to sand without clogging the paper.  Cleaning to remove blush is not necessary unless you are working in freezing rain. 

Recoat with Paint or Varnish after 7 day full cure.  Sand to 220 grit, remove dust with water and a clean cloth, allow to dry thoroughly for at least 1 hour before applying coating.  Two part Polyurethane coatings over Epoxy will last longer and be more scratch resistant than Enamel paints. 

POT LIFE and CURE TIMES:

Pot Life and sanding time will vary depending on temperature, mixed volume, time in the mixing container and laminate thickness.  Pot life and cure time will roughly double for a 8C drop in temperature, and ½ for an 8C rise.  

To extend working time pour the mixed epoxy into a paint tray or spread onto the work surface as soon as possible, a thin film will take longer to gel.  Volumes over 100 ml will get HOT if left in the mixing pot.

Fast and Slow hardeners are blendable to customise pot life and will cure as low as 5C.     

           

HARDENER

POT LIFE @ 22C/71F

WORKING

(GEL) TIME

SANDABLE

 

POT LIFE@

12C/54F

SANDABLE

FULL CURE

855 FAST

8 -10 MIN

15 -18 MIN

6 -8 HRS

18 – 20 MIN

12 – 14 HR

7 DAYS

856 SLOW

15-20 MIN

30 -35 MIN

10 – 12 HRS

35 – 40 MIN

20 – 24 HR

7 DAYS